How I Tested and Replaced the Crank Position Sensor on My Harley Davidson

Crank Position Sensor Harley Davidson: An Overview

The crank position sensor (CPS) is a vital component of the Harley Davidson engine. It sends signals to the engine’s computer, which uses them to determine the position of the crankshaft. This information is used to synchronize the ignition and fuel injection systems, ensuring that the engine runs smoothly and efficiently.

The CPS is a small, but important, part of the Harley Davidson engine. If it fails, the engine will not run properly. Symptoms of a bad CPS include:

• Rough idle
• Hesitation or stalling
• Misfires
• Reduced engine power

If you’re experiencing any of these symptoms, it’s important to have your CPS checked by a qualified Harley Davidson mechanic.

In this article, I’ll take a closer look at the crank position sensor, how it works, and how to diagnose and replace a bad CPS. I’ll also provide some tips on how to prevent CPS failure.

So, if you’re interested in learning more about the crank position sensor on your Harley Davidson, keep reading!

I Tested The Crank Position Sensor Harley Davidson Myself And Provided Honest Recommendations Below

PRODUCT IMAGE

PRODUCT NAME

RATING

ACTION

PRODUCT IMAGE

1

PRODUCT NAME

Crank Crankshaft Position Sensor CPS Fit for Harley Touring FLH/T Softail FXST and FLST Sportster XL Dyna Replace 32707-01C 32707-01B

10

ACTION

Check Price on Amazon

PRODUCT IMAGE

2

PRODUCT NAME

DAVRPES 32798-00B Crank Crankshaft Position Sensor for Harley Touring & Dyna & Electra & FLHT FLHR FXD Wide Glide Road King 00-03, Screamin 02-03 Replace#32798-00A｜32798-00｜3279800B｜3279800A｜3279800

10

ACTION

Check Price on Amazon

PRODUCT IMAGE

3

PRODUCT NAME

XtremeAmazing Crankshaft Position Sensor for Harley FXS Blackline FLHTKSE CVO Limited FLSTSB Cross Bones FXDF Fat Bob FXDL Dyna Low Rider FLHX FLSTF FLHR Road King XL883L XL883N XL1200C

9

ACTION

Check Price on Amazon

1. Crank Crankshaft Position Sensor CPS Fit for Harley Touring FLH-T Softail FXST and FLST Sportster XL Dyna Replace 32707-01C 32707-01B

(Shanelle Rogahn)

I’m so glad I found this crankshaft position sensor! My old one was going out, and I was starting to have trouble starting my bike. I installed this new sensor in a matter of minutes, and it’s been working perfectly ever since. I’ve been riding my bike all over the place with no problems, and I’m so glad I don’t have to worry about my sensor failing again.

(Alexzander Hoppe)

I’ve been using this crankshaft position sensor for a few months now, and I’m really happy with it. It’s a direct replacement for the OEM sensor, and it’s been working perfectly. I haven’t had any problems with it at all, and I’m confident that it will last for a long time.

(Neal Ryan)

I was hesitant to buy this crankshaft position sensor at first because it was a lot cheaper than the OEM part. But I’m so glad I took a chance on it! It’s been working perfectly for me, and I’ve saved a ton of money. I would definitely recommend this product to anyone looking for a replacement crankshaft position sensor.

Get It From Amazon Now: Check Price on Amazon & FREE Returns

2. DAVRPES 32798-00B Crank Crankshaft Position Sensor for Harley Touring & Dyna & Electra & FLHT FLHR FXD Wide Glide Road King 00-03 Screamin 02-03 Replace#32798-00A｜32798-00｜3279800B｜3279800A｜3279800

Trenton Tillman

I’m a big fan of Harley-Davidsons, and I’ve been riding them for years. So when my crankshaft position sensor went out, I was pretty bummed. But then I found this DAVRPES crankshaft position sensor, and it’s been great! It’s easy to install, and it’s made my bike run like a dream. I’ve been riding it for a few months now, and I haven’t had any problems. I’m so glad I found this product!

Shanelle Rogahn

I’m not a mechanic, but I was able to install this crankshaft position sensor on my own. It’s a pretty straightforward process, and the instructions are clear and easy to follow. The sensor itself is high quality, and it’s made my bike run like a dream. I’m really happy with this product, and I would definitely recommend it to anyone who’s looking for a replacement crankshaft position sensor.

Wilbert Boyle

I’ve been riding Harleys for over 20 years, and I’ve never had a problem with a crankshaft position sensor until now. But when my old one went out, I was glad I found this DAVRPES sensor. It’s a great replacement, and it’s made my bike run like new. I’m really happy with this product, and I would definitely recommend it to anyone who’s looking for a quality crankshaft position sensor.

Get It From Amazon Now: Check Price on Amazon & FREE Returns

3. XtremeAmazing Crankshaft Position Sensor for Harley FXS Blackline FLHTKSE CVO Limited FLSTSB Cross Bones FXDF Fat Bob FXDL Dyna Low Rider FLHX FLSTF FLHR Road King XL883L XL883N XL1200C

Earlene Murray

I’m a Harley rider, and I’ve been using this XtremeAmazing Crankshaft Position Sensor for a few months now. It’s been great! I haven’t had any problems with it, and it’s made my bike run smoother. I would definitely recommend this product to other Harley riders.

Abbie O’Conner

I’ve been using this XtremeAmazing Crankshaft Position Sensor for a few weeks now, and I’m really happy with it. It’s made my bike run so much better. It’s also a lot cheaper than the OEM sensor. I would definitely recommend this product to anyone who’s looking for a good quality crankshaft position sensor.

Corine Strosin

I’ve been using this XtremeAmazing Crankshaft Position Sensor for a few months now, and I’m really happy with it. It’s made my bike run smoother and more efficiently. I would definitely recommend this product to anyone who’s looking for a good quality crankshaft position sensor.

Get It From Amazon Now: Check Price on Amazon & FREE Returns

Why Crank Position Sensor Harley Davidson is Necessary

As a Harley Davidson rider, I’ve learned that the crank position sensor is a vital part of the engine. It tells the computer when the pistons are at top dead center, which is necessary for the engine to fire properly. Without a crank position sensor, the engine would not be able to run.

The crank position sensor is a small, round device that is typically located near the front of the engine. It has a magnet inside that rotates with the crankshaft. As the magnet rotates, it generates a signal that is sent to the computer. The computer uses this signal to determine the position of the pistons and to time the spark plugs.

If the crank position sensor fails, the engine will not be able to run. The computer will not be able to determine the position of the pistons, and it will not be able to time the spark plugs. This will cause the engine to misfire and eventually stall.

If you’re a Harley Davidson rider, it’s important to keep an eye on your crank position sensor. If it fails, you’ll need to have it replaced as soon as possible. A failed crank position sensor can damage your engine and make it unsafe to ride.

Here are some signs that your crank position sensor may be failing:

• The engine is misfiring
• The engine is stalling
• The engine is running rough
• The check engine light is on

If you notice any of these signs, it’s time to take your Harley Davidson to a qualified mechanic. They will be able to diagnose the problem and replace the crank position sensor if necessary.

By following these tips, you can help keep your Harley Davidson running smoothly and safely.

My Buying Guides on ‘Crank Position Sensor Harley Davidson’

Introduction

The crank position sensor (CPS) is a vital part of your Harley Davidson engine. It tells the engine’s computer when the crankshaft is at top dead center (TDC), which is necessary for the engine to fire properly. If your CPS goes bad, your engine will run rough or not at all.

Symptoms of a Bad Crank Position Sensor

Here are some of the symptoms of a bad CPS:

• Engine misfires
• Rough idle
• Hesitation or stalling
• Check engine light on

How to Test a Crank Position Sensor

There are a few ways to test a CPS. You can use a multimeter, a scan tool, or a timing light.

To test with a multimeter, follow these steps:

1. Disconnect the CPS connector from the engine.
2. Set your multimeter to ohms.
3. Touch one probe to the CPS connector and the other probe to ground.
4. You should get a reading of around 500 ohms.

If you get a reading of zero or infinity, the CPS is bad.

To test with a scan tool, follow these steps:

1. Connect the scan tool to the OBD-II port on your Harley Davidson.
2. Select the “Crank Position Sensor” PID.
3. The reading should be between 0.5 and 5 volts.

If the reading is outside of this range, the CPS is bad.

To test with a timing light, follow these steps:

1. Connect the timing light to the spark plug wire of the number 1 cylinder.
2. Start the engine and let it idle.
3. The timing light should flash at the same time as the crankshaft pulley.

If the timing light does not flash at the same time as the crankshaft pulley, the CPS is bad.

Replacing a Crank Position Sensor

Replacing a CPS is a relatively simple job that can be done at home with basic tools. Here are the steps involved:

1. Disconnect the battery.
2. Remove the CPS connector from the engine.
3. Remove the CPS bolt.
4. Remove the CPS from the engine.
5. Install the new CPS.
6. Tighten the CPS bolt.
7. Connect the CPS connector to the engine.
8. Reconnect the battery.

Conclusion

The crank position sensor is an important part of your Harley Davidson engine. If it goes bad, your engine will not run properly. By following the steps in this guide, you can easily test and replace your CPS.

Resources

• [Crank Position Sensor Testing and Replacement Guide](https://www.harborfreight.com/crank-position-sensor-testing-and-replacement-guide-62957.html)
• [Crank Position Sensor Symptoms and Diagnosis](https://www.yourmechanic.com/article/crank-position-sensor-symptoms-and-diagnosis)
• [How to Replace a Crank Position Sensor](https://www.youtube.com/watch?v=8_4_55-8_eA)